Dronetag DRI
USA
EU
compliant
$55.00
The smallest and lightest device offering affordable Direct / Broadcast Remote capability to drone manufacturers or integrators. It offers a cost-effective, lightweight, and user-friendly option to manufacture remotely identifiable drones. With the Dronetag DRI solution, manufacturers are on a frictionless path toward the production launch of Standard Remote ID (US) and C-class (EU) drones.
DRI comes in two variations (please select your variant below):
- with a U.FL port for an external antenna (includes Bluetooth Wire antenna)
- with a built-in antenna
As an accessory to the DRI version with an External U.FL Antenna port, you can purchase a Bluetooth Tube Antenna with a U.FL connector. This optional antenna offers stronger performance than the Wire Antenna that is included in the package.
Manuals & guides available
We strongly recommend exploring our comprehensive website at help.dronetag.com
Check product availability
Some of our items are currently on backorder, check the availability before you order
Be aware of cancellation fees
Orders are subject to cancellation fees, as outlined in our Terms and Conditions
AppWeb, iOS & Android
CompatibilityAll standard Pixhawk controllers - PX4 or Ardupilot
Remote IDBroadcast / Direct
Battery lifeno battery
Dimensions22.5 x 16 x 5 mm
Weight1.5 g / 0.5 g (with/out JST connectors)
Plug & Play for Pixhawk Cube or Similar You only need one cable to add Remote ID to your aircraft. Dronetag DRI is compatible with all standard Pixhawk controllers running PX4 or Ardupilot. Plug it into your TELEM port, configure the appropriate baud rate, and you are ready to fly. Not using MAVlink, PX4 or Ardupilot FCs? Having custom firmware? No problem; we can customize our solution to your needs.
UART Pass-Through Integration Dronetag DRI will not take away any of your existing ports. Thanks to our UART forwarding feature, you can integrate it between the flight controller and your serial peripheral.
Two Options One that comes with a U.FL connector for an external antenna and the second with an internal antenna already on board.
Flexible Mounting
Dronetag DRI is a small board, so you can either use double-sided tape or M2 screws to mount it in the desired place.
ASD-STAN EN 4709-002 & ASTM F3411-22 Compliant
Suitable for all regions adopting any of those standards. Broadcast over Bluetooth 4 & 5 to up to 3 km (1.8 miles) range. OTA Firmware Updates
Comes with Standardized SN
Our DRI module already has ANSI/CTA-2063-A serial number baked inside. Refer to this SN during the compliance process.
Dronetag DRI with External U.FL Antenna Port
- 1x Dronetag DRI
- 1x Cable 6-PIN GH to 6-PIN GH 10 cm
- 1x Bluetooth Wire Antenna
Dronetag DRI with Built-in Antenna Port
- 1x Dronetag DRI
- 1x Cable 6-PIN GH to 6-PIN GH 10 cm
- Remote ID types
- Direct (EU) / Broadcast (US)
- Short-range radio
- Bluetooth 2.4 GHz
- Sensors
- None, data read from flight controller
- Average current consumption
- 3 mA
- Maximum current consumption
- 10 mA
- Mounting
- M2 holes or double-sided tape
- Operating temperature
- -40 °C to 85 °C (-40 °F to 185 °F)
- Dimensions
- 22.5 × 16 × 5 mm (0.89 × 0.62 × 0.19 in)
- Weight
- With JST connectors 1.5 g (0.56 oz)
Without JST connectors 0.5 g (0.017 oz) - Indicators
- RGB LED to show the state
- Antenna
- Variant with internal or external one
- Antenna Connectors
- Optionally 1 × U.FL (IPEX compatible)
- Communication Connectors
- 2 × JST GH 6-pin (1.25 mm pitch)
- Communication Protocol
- UART (3.3 – 5 V tolerant)
- Supported Message Protocol
- MAVlink 2
- Supported baud rates
- Standard ones - configurable in Dronetag app
- Input voltage
- 3.3 – 17 V
- Input voltage regulator
- Low-noise buck converter
- Remote ID Standards
- ASD-STAN EN 4709-002 & ASTM F3411-22
- Certifications
- Uses FCC/CE approved radio module
- Remote ID technology
- Bluetooth 4.0 Legacy + 5.0 Long Range
- Compliant
- EU
USA
You might also like
The smallest and lightest device offering affordable Direct / Broadcast Remote capability to drone manufacturers or integrators. It offers a cost-effective, lightweight, and user-friendly option to manufacture remotely identifiable drones. With the Dronetag DRI solution, manufacturers are on a frictionless path toward the production launch of Standard Remote ID (US) and C-class (EU) drones.
DRI comes in two variations (please select your variant below):
- with a U.FL port for an external antenna (includes Bluetooth Wire antenna)
- with a built-in antenna
As an accessory to the DRI version with an External U.FL Antenna port, you can purchase a Bluetooth Tube Antenna with a U.FL connector. This optional antenna offers stronger performance than the Wire Antenna that is included in the package.